美國奧林巴斯-泛美超聲波脈沖發射接收器panametrics model 5073PR型概述：
脈沖發生器-接收器具有適用于手動控制和基于計算機的檢測系統的寬帶負尖波激勵脈沖和極高的材料穿透性能，從而提高了自動檢測的性能。Olympus Panametrics的脈沖發生器-接收器與基于計算機的系統一起使用，可完成那些要求具有高材料穿透性能且超聲信號的極低噪音放大性能的自動超聲檢測應用。
美國奧林巴斯-泛美超聲波脈沖發射接收器panametrics model 5073PR型具有超高性能的寬帶（75MHz）、負尖峰激勵脈沖發生器，尖峰激勵脈沖器可以優化寬帶響應和近表面分辨率；
阻尼、脈沖能量、重復速率可選；
可選20MHz低通濾波器；
可選高通濾波器用于快速恢復時間和低頻噪聲抑制；
與泛美的無級閘門、閘門峰值探測器、閘門閾值報警和自動系統兼容；
美國奧林巴斯-泛美超聲波脈沖發射接收器panametrics model 5073PR型的脈沖發生器：脈沖重復速率0.2~10kHz可調；
大脈沖振幅：-180V（100Ω阻尼，第四檔能量位置，無外部載荷）；
阻尼范圍（脈沖回波模式或穿透模式）：12/14/17/20/25/33/50或100Ω可選；
脈沖上升時間（50Ω阻尼，小能量）：＜2ns（10%-90%）；
脈沖能量（CE2/2）：2、4、8和16微焦（可選）；
同步信號輸出：3.5V（阻尼=50Ω），在2.4V上可驅動26個標準TTL負載；
外部觸發要求：+2.4V（大7V）（1000pf與10kΩ串聯），小脈沖寬度200ns；
接收器輸入阻抗（穿透模式）：100Ω（線性范圍），信號大于線性范圍時約100Ω；
大輸入功率：大平均功率400mW；
相位：反相或不反相（內置選擇開關）；
衰減器：0~49dB，1dB步進；
電壓增益（帶寬35MHz，阻尼=50Ω）：0~39dB，1dB步進；
輸出噪聲：典型7mVp-p（帶寬75MHz）；
高通濾波器：1kHz（out）或5MHz（選擇）；
低通濾波器：75MHz（大）或20MHz（選擇）；
脈沖發生器與接收器之間的絕緣：在50MHz時小53dB（典型62dB）；
大輸出電壓波動：±1.0Vpk（阻尼=50Ω）；
輸出阻抗：50Ω；
美國奧林巴斯-泛美超聲波脈沖發射接收器panametrics model 5073PR型電源要求：100/120/220/240VAC，50~60Hz，7.5W；
保險絲：1/4A（100/120VAC），1/8A（220/240VAC）；
尺寸：178x89x232mm；
重量：2.3kg；
工作溫度：0~50℃；
美國奧林巴斯-泛美超聲波脈沖發射接收器panametrics model 5073PR型參數規格：
|
UNIT
|
5072PR,5073PR,5077PR
|
|
Input/Output:
|
External Trigger
In, Sync Out, RF Out, T/R and R: All BNC female connectors
|
|
Power Main
Requirements:
|
100/120/220/240
VAC, 50/60 Hz
|
|
Operating
Temperature:
|
0-50°C
|
|
Size and Weight:
|
7" W x
3.5" H x 9.1" D (178 mm x 89 mm x 232 mm); 5 lbs (2.3 kg)
|
Specifications
|
PULSER
|
5073PR
|
|
Pulse Type
(main bang):
|
Negative Impulse
|
|
Rise Time
(10% to 90%):
|
Typically <2
ns
|
|
Available Pulse
Voltage:
(no load)
|
-180 V
|
|
Available Pulse
Energy:
|
2, 4, 8, or 16
µjoules
|
|
Damping:
|
12, 14, 17, 20,
25, 33, 50, or
100 ohms
|
|
Pulse Width:
|
N/A
|
|
Mode:
|
Pulse Echo or
Thru-Transmission
|
|
Isolation (53 dB
min):
|
Typically 62 dB
at 50 MHz
|
|
Pulse Repetition
Rate:
(Internal)
|
200, 500, 1000,
2000, 5000, 10000, or 20000 Hz
|
|
Pulse Repetition
Rate:
|
0-10 kHz
|
|
Synch Output
Pulse:
|
|
|
External Trigger
Input:
(in series with 10 Kohms)
|
2.4 V into 1000
PF
200 ns minimum pulse width
|
|
RECEIVER
|
5073PR
|
|
Maximum
Bandwidth:
(-3 dB, RL=50 ohms)
|
1 kHz - 75 MHz
|
|
Voltage Gain:
|
0-39, 1 dB steps
(RL=50 ohms)
|
|
Phase:
|
inverting or
non-inverting (internal switch)
|
|
Attenuator Range:
|
0-49, 1 dB steps
(RL=50 ohms)
|
|
High Pass Filter:
|
1 kHz (out) or 5
MHz
|
|
Low Pass Filter:
|
75 MHz (out) or
20 MHz
|
|
Noise:
|
200 µV pk-pk
typical, referred to input, BW=75 MHz
|
|
Max Signal
Output:
|
+/-1V pk.,
terminated in 50 ohms
|
|
Input
Resistance:
(Thru-Transmission)
|
100 ohms linear
range
50 ohms at levels > linear range
|
|
Output Impedance:
|
50 ohms
|
|
Maximum Input
Power:
|
400 mW
|
美國奧林巴斯-泛美超聲波脈沖發射接收器panametrics model 5073PR型英文簡介：
Model 5073PR:75
MHz (-3 dB) ultrasonic bandwidth with fast rise time spike pulser extends
performance for work with 50 MHz transducers in applications that challenge
limits in axial and near surface resolution.
These affordable
and reliable manually controlled pulser-receivers provide the perfect building
blocks for both conventional and high frequency applications. Each instrument
is designed for superior low noise receiver response and high performance
pulser control.
When used with an appropriate transducer and analog or digital oscilloscope,
Panametrics pulser-receivers provide the perfect starting point for ultrasonic
flaw detection, thickness gaging, materials characterization, and transducer
characterization.
奧林巴斯-泛美超聲波脈沖發射接收器Features &
Benefits
Three models
provide optimization for both conventional and high frequency
applications
Broadband Spike (5072 and 5073) or Tunable Square Wave (5077) transducer
excitation models available
Front panel controls permit quick and easy setup of parameters for optimizing
signal response
Each model delivers a wide dynamic range with 1 dB sensitivity adjustments
made through a front panel lever switch
Low noise receiver amplification and pulser optimization ensure superior
signal-to-noise characteristics
Superior isolation of receiver from pulser main bang when operating in
thru-transmission mode
+/-1 volt RF output into 50 ohm load
Small, lightweight packaging
